DJI Tiny Trainer HD (3.5) (Ready To Fly) – Five33

$ 10.50

5 (755) In stock

These Ready to Fly Drones are Hand Built in our Tennessee based shop and every build is test flown by World Champion Evan Turner before heading out the door. This is a custom built drone that is destined for a podium. We only use the best performing gear that we trust in our own builds. Want our tiny trainer HD tune!?
These Ready to Fly Drones are Hand Built in our Tennessee based shop and every build is test flown by World Champion Evan Turner before heading out the door. This is a custom built drone that is destined for a podium. We only use the best performing gear that we trust in our own builds. Want our tiny trainer HD tune!? Diff available at the bottom of this page! Specifications Frame: TinyTrainer 3.5 Motors: 1804 No Brand Motors AIO: BetaFPV 4S F405 AIO VTX: DJI O3 VTX IncludesQty 1 Ready to fly Racing Drone ready to bind to your receiver and fly. Qty 1 Free set of Props Limitations of LiabilityPurchasers of this product expressly agree that in the event of any defects of a FlyFive33 LLC product, the only available remedy will be a refund not to exceed the actual amount paid by the purchaser for the product purchased. FlyFive33 LLC shall not be liable for any special, incidental, or consequential damages that result from the use of, failure to complete safety checklist, or the inability to use, the materials sold through this site or the performance of the products, even if FlyFive33 LLC has been advised of the possibility of such damages.If you believe a product is defective, please notify our Customer Service department immediately by email at flyfive33@gmail.com. All claims relating to defective products are limited to refunds of the purchase price and will be honored only when made within 30 days of the date the product was shipped. Requests for refunds will not be honored where products are damaged or fail through misuse or in violation of any of the Returns and Refund Policy. Want our tiny trainer HD tune!? Diff available here for betaflight 4.4.3! This was made for a TTHD with HDZero and Crossfire components. Please contact our customer support chat in the bottom right of our website for any questions related to this. # name: TTHD# featurefeature -RX_PARALLEL_PWM# serialserial 3 1 115200 57600 0 115200# ledled 0 0,0::C:2led 1 1,0::C:2# auxaux 0 0 0 1300 2100 0 0aux 1 15 0 900 1700 0 0# masterset dyn_notch_count = 1set dyn_notch_q = 500set acc_hardware = NONEset acc_calibration = 48,29,-4071,1set serialrx_provider = CRSFset dshot_bidir = ONset motor_poles = 14set motor_output_reordering = 3,2,1,0,4,5,6,7set align_board_yaw = 225set ibata_scale = 240set osd_vbat_pos = 2049set osd_craft_name_pos = 2081set osd_disarmed_pos = 2346set osd_displayport_device = MSPset vtx_band = 0set vtx_channel = 0set vtx_power = 0set vtx_freq = 0set displayport_msp_serial = 3set name = TTHDprofile 0profile 1profile 2# restore original profile selectionprofile 0rateprofile 0# rateprofile 0set rates_type = BETAFLIGHTset roll_rc_rate = 80set pitch_rc_rate = 80set yaw_rc_rate = 80set roll_srate = 70set pitch_srate = 70set yaw_srate = 70rateprofile 1rateprofile 2rateprofile 3rateprofile 4rateprofile 5# restore original rateprofile selectionrateprofile 0# save configurationsave